electric resistance welded pipe
"
機械で造る BS6323-6 DOM の鋼鉄管 35mm の壁厚さの継ぎ目が無い溶接された鋼鉄管
Standard: BS6323-6 Seamless and Welded Steel Tubes for Automobile,Mechanical and General Engineering Purposes Part 6: Specific requirements for cold finished electric resistance welded(including induction welded) steel tubes Applications: for Auto industry / for machinery use/mechanical and general engineering purposes Size range: O.D.:6-350mm W.T.:1-35mm L:max12000mm Method of Manufacture: The tubes are manufactured from flat rolled strip, longintudinally welded continuously
亜鉛めっき鋼管（ERW、一般配管用、外径30～325mm）
SGP Welded Carbon Steel Pipe (ERW Steel Tube) for Ordinary Piping Material This product is an electric-resistance-welded (ERW) carbon steel pipe designed for ordinary/utility piping —typically used to convey steam, water, oil, gas, air, and other general fluids under relatively low service pressure . Specifications Manufacturing process: High-frequency ERW longitudinal seam. Typical size range (SGP / JIS ordinary piping): OD 10.5–508.0 mm (DN 6A–500A) with corresponding
Q235 建築用用用炭鉄構造材の溶接式四角管,冷引式および熱巻き式
Q235 Carbon Structural Steel Welded Square Pipe for Architecture Material Q235 is a mild (low-carbon) structural steel widely specified in China under GB/T 700 . It is commonly produced into welded square hollow sections (SHS) for building and architectural steelwork because it balances strength, weldability, formability, and cost efficiency . Specifications Typical supply options for carbon steel welded square pipe (SHS) : Manufacturing : ERW (Electric Resistance Welded),
ASTM A500 グレード C 冷たく溶接された炭素鋼構造型四角管 50 ksi 耐力
ASTM A500 Grade C Cold-Formed Welded Carbon Steel Structural Square Tubing Material ASTM A500 Grade C is a cold-formed, electric-resistance-welded (ERW) carbon steel structural hollow section (HSS) in a square profile, designed for welded, riveted, or bolted construction (e.g., bridges, buildings, and general structural fabrication). Specifications Product form: Square structural tubing (HSS) Manufacturing: ERW from flat-rolled steel; welded across thickness. (Inside flash is
DOM 鋼管 ERW 精密機械用冷引丸管
DOM Steel Pipe (ERW Cold Drawn Mild Steel Round Tube) for Precision Machinery 1. Material This product—commonly referred to as DOM (Drawn Over Mandrel) tubing —is a high-strength, precision round tube manufactured using a combination of electric resistance welding (ERW) and cold drawing over a mandrel. It’s typically fabricated from mild carbon steel grades such as SAE 1020, 1026 , and in some cases ST52.3 . 2. Specifications Manufacturing Process : Starts with an ERW "mother
JIS G3472 STAM500G High Strength ERW Welded Steel Tube with Good Formability and Consistent Dimensions for Automotive Structural Pipe
Electric-Resistance Welded Carbon Steel Structural Pipe for Automotive Applications Material This product is an electric-resistance welded (ERW) carbon steel tube manufactured from hot-rolled or cold-rolled steel strip/coil and welded continuously. It is designed specifically for automotive structural applications, meeting the Japanese standard JIS G3472 for “Electric Resistance Welded Carbon Steel Tubes for Automobile” (automotive structural use).The material is carbon steel
S31260 デュプレックスステンレススチールチューブ - 塩化物耐腐食性のある高強度溶液 流体ガス輸送のために焼却
S31260 Industry Seamless Welded Stainless Steel Tube For Fluid Gas Transport S31260 Seamless and Welded Duplex Stainless Steel Tube UNS S31260 is a 25Cr duplex stainless steel tube grade designed for industrial fluid and gas transport where higher strength, chloride corrosion resistance, and stress corrosion cracking resistance are required. Compared with standard 304/316 austenitic stainless steel tubing, S31260 offers a stronger duplex microstructure and higher resistance
EN 10217-4 P215NL 低温性能用 溶合金のない鋼管の電動溶接式ERW
EN 10217-4 P215NL P265NL Welded Steel Tube: ERW Electric Welded Non-Alloy Steel Tubes For Low Temperature Properties Introduction EN 10217-4 is a European standard that specifies the technical delivery conditions for electric welded non-alloy steel tubes for low temperature properties. This standard covers the requirements for tubes made from non-alloy and fine grain steel suitable for low temperature service. In this article, we will explore the key features, chemical
冷たい折りたたみステンレス鋼U型パイプ TP304/304L TP316/316L TP321 交換器用
Stainless Steel U Shape Pipe – Cold-Bent U-Shaped Steel Pipe for Heat Exchangers Material Overview Stainless Steel U Shape Pipes (U-bent tubes) are fabricated by cold bending seamless or welded stainless steel heat exchanger tubes into precise U or multi-U geometries, followed by stress-relief or solution annealing where required. They are designed for shell-and-tube heat exchangers, condensers, boilers, and feedwater heaters operating under high temperature and pressure, and
